Alarm Lock DL1300 Instrukcja Obsługi Pobierz pdf (Strona 12)

When a valid code is entered and the batteries are weak, the

red & green LED's will light and the sounder will sound for 4

seconds. The DL1200 uses two '123' Type Lithium batteries

(Duracell P/N CR17345). The lock will function with weak

batteries; however be sure to replace them as soon as

possible.

If the DL1200 is ever without power for less than 1 minute

(such as when replacing batteries), the DL1200 will continue its

operation undisturbed--programming remains unaffected due

to power provided by capacitors inside the lock. If the DL1200

is without power for greater than one minute, you have two

choices--you can (1) retain the lock programming or (2) erase

all programming. If you choose to erase all programming, the

DL1200 will revert to its original factory default configuration

("out of the box").

CAUTION: Do not press any keys while batteries are dis-

connected unless you intend to erase all programming.

1. Insert key in cylinder and turn counterclockwise to al-

low access to the battery compartment screw. With the

supplied 5/64" Allen wrench, loosen the battery cover

screw only until the battery cover is able to slide off.

2. Pull out the battery pack and quickly replace both

batteries - within 1 minute.

3. If you do not hear the 3 beeps when power is re-

applied, all programming and settings have been re-

tained, and the lock is ready for use. Go to step 5.

4. If you do hear 3 beeps when power is re-applied, do

not press any keys for 15 seconds. After the 15

second period, the LED will flash red 6 times and 6

beeps will sound. Reset the clock using functions 38, 39

and 40.

5. Slide the battery cover back in place and tighten the

screw.

If you accidentally press a key (or fail to replace the batteries

within 1 minute), use the Retain Lock Programming proce-

dure below:

Retain Lock Programming

1. Re-install battery pack.

2. Do not press any keys for 10 seconds.

If you do not hear any beeps or if you hear 3 beeps (one

per second), the previous lock programming is retained and

the lock is now ready for use. If you test the DL1200 and

find the lock programming is lost, you may erase all pro-

gramming and return the DL1200 to its original factory set-

tings, as described below.

Battery Replacement

Erase All Programming

RESTORE FACTORY DEFAULT (original "out of box" set-

tings that were set at the factory will be loaded).

1. Enter the current Master Code (if not known, proceed di-

rectly to ALTERNATIVE METHOD, below). Wait for the

green light. The lock will unlock.

2. Within 5 seconds (or current Pass Time interval), press

the function ; 000 ;.

3. Listen for 6 beeps. The lock will re-lock. All settings and

programming have been erased. Proceed directly to page

12, Quick Start, and follow the procedure "Enter Pro-

gram Mode and Change Factory Master Code".

ALTERNATIVE METHOD

Note: This method requires the lock first be removed

from the door.

1. Insert key in cylinder and turn counterclockwise to

allow access to the battery compartment screw. With

the supplied 5/64" Allen wrench, loosen the battery

cover screw only until the battery cover is able to

slide off.

2. Disconnect the battery pack.

3. Remove the back plate by unscrewing the two Phil-

lips head screws. Note: Some models have four

Phillips head screws. Be careful not to damage the

motor drive wires.

4. Locate jumper header JP1 near the top of the

printed circuit board and install the jumper (provided)

across pins 1 and 2 of JP1.

5. Press and hold down ; for 10 seconds (to en-

sure all power is drained from the lock) and release.

6. Connect the batteries and--within 5 seconds--press

and hold ;. After hearing 6 additional beeps,

release ;. If you do not hear these 6 additional

beeps, you must start over at step 2. Failure to fol-

low this exact procedure can result in erratic lock

behavior.

7. Test by pressing the default Master Code of

12345 (a beep will sound and

the lock will unlock).

8. Remove the jumper from JP1 pins 1 and 2 and

place jumper on 1 pin for storage.

9. Carefully reinstall the back plate STRAIGHT onto

the lock body. Be careful not to pinch or damage the

motor drive wires. While inserting the back plate, be

sure the rear pin of the tailpiece inserts into the spin-

dle hole--check this alignment after installation by

pushing on the spring-loaded tailpiece to verify that it

smoothly moves up and down. Replace the two (or

four) Phillips head screws to secure the back plate.

Note: It may be necessary to tighten the battery

screw previously loosened in step 1.

10. Re-mount the lock on the door. With the battery

back inside its compartment, slide the battery cover

back in place and tighten the screw.

All settings and programming have been erased.

Proceed directly to page 12, Quick Start, and follow

the procedure "Enter Program Mode and Change

Factory Master Code".

1 2 ... 7 8 9 10 11 12 13

Komentarze do niniejszej Instrukcji

Brak uwag

Alarm Lock DL1300 Instrukcja Obsługi Strona 12

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Alarm Lock DL1300