Alarm Lock Trilogy PL3000 Instrukcja Obsługi Pobierz pdf (Strona 15)

Function Card #1

IMPORTANT NOTE:

When programming is sent from DL-Windows (or an AL-DTM) to the lock, Function Cards 1, 2, 8, and 9 will be overwritten with

the existing data in DL-Windows for the User Locations 298, 299, 297 and 300, respectively. Therefore, to continue to use

Function Cards 1, 2, 8 and 9 that were enrolled at startup with DL-Windows, be sure to enroll those same Function Cards 1,

2, 8 and 9 used at startup into the correct locations within DL-Windows. For complete instructions, see the DL-Windows

User Guide, OI237.

Initiates PC Communications (User 298)

Function Card #1 is used to initiate PC communications from your PC and the PL3000 lock or from the PL3000 to your

PC. Your PC should be running DL-Windows (version 3.0.4 or later) and should be ready to send its data to or from the

PL3000. For more information, please see the DL-Windows User Guide, OI237. The following details the basic steps:

Send Information to Lock

1. Connect an AL-PCI2 cable to the COM Port at the rear of your PC to the PL3000 lock, observing tab direction (tab

to black socket).

2. In DL-Windows, press the Lock button to open the Lock Data screen.

3. Click Send/Receive (on the Lock Data screen or the Comm button), and select Send to Lock.

4. In the Send to Lock dialog, deselect All, and select Users and Time/Date.

5. Click Start. DL-Windows is now waiting for Function Card #1 to start the data transfer.

6. Present Function Card #1 to the lock.

7. Data will now be sent to the lock. In DL-Windows, the Status Bar in the lower left hand corner of the Send to

Lock screen will indicate the data transfer. The Model Type and Firmware Version will be displayed on the Send

to Lock screen.

8. After the data transfer is complete, “Send To Lock Successful” will be displayed in the Status Window (lower left

hand corner) of the Send to Lock screen.

9. At the end of the transfer process, the PL3000 will sound a series of beeps. You can disconnect the AL-PCI2 ca-

ble.

10. Test New User Cards. Verify that each new user Card allows access when presented to the lock. Test each

lock that has been programmed.

Receive Information from Lock

1. Open DL-Windows and open the Account and lock from which you would like to receive data.

2. Press Lock to open the Lock Data screen.

3. Click Send/Receive (on the Lock Data screen or the Comm button). Select Receive from Lock.

4. In the Receive from Lock dialog, select All.

5. Connect AL-PCI2 cable to your computer COM port and to the lock, observing tab direction (tab to black socket).

6. In the Receive from Lock dialog, click Start. DL-Windows is now waiting for Function Card #1 to start the data

transfer.

7. Present Function Card #1 to the lock.

8. Data will now be received from the lock. The Receive from Lock screen will display the Model Type and Firm-

ware Version.

8. When transfer is complete, the PL3000 will sound a series of beeps. You can disconnect the AL-PCI2 cable.

9. The Lock Changes screen will appear detailing the disparity between what was seen in the lock program received

and the corresponding software within DL-Windows.

Once Function Cards are enrolled during startup, they can quickly perform several functions when presented to the lock. The

section below describes how each card is used to perform its specialized function.

Function Card # 1

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 27 28

Komentarze do niniejszej Instrukcji

Brak uwag

Alarm Lock Trilogy PL3000 Instrukcja Obsługi Strona 15

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Alarm Lock Trilogy PL3000